antweight/beetleweight parts clearout

[josh]

A few things to get rid of:
4 x single cell 138mah turnigy lipo £2 each
3x 2cell 180mah lipo £4 each
2x savox s57mg digital servos (no plugs) £8 each
1x 2cell 25c 130mah lipo
1x turnigy brushless motor 20.5mm dia £10
2x single motor controllers 2a could be used in ants or beetles £25 for the pair
1x 12amp brushless esc £6
1x orange 4ch 2.4 dsm2 reciever £8
1x 6v voltage regulator £2
2x v tail mixers £2 each
1x 6amp brushless speed controller £6
3x turnigy 4g servos £3 each
4x 3d printed wheel to fit 3mm gear motor shaft 21x10 mm £4 a pair


may also sell my eggbeater set up (just the weapon) for the right price as I have too many robots, 22mm dia brushless outrunner with a 30mm dia p20 cnc cut and nitride hardened eggbeater and support bearing. this however was very expensive to produce and I won't sell unless I get an offer around what it cost me. it can be seen here:

[harry hills]

Re: antweight/beetleweight parts clearout

ill take the turnigiy servos, voltage regulator and posiblyt the savrox servos.

what plugs are on the 180mah lipos?

[josh]

Re: antweight/beetleweight parts clearout

sure, the plugs atm are micro jst I think they're called? I can put on standard 0.1 plugs if you would prefer though

[harry hills]

Re: antweight/beetleweight parts clearout

nah, it ok ive changed my mind about them, when is the next event your planning to go to?

[josh]

Re: antweight/beetleweight parts clearout

I won't be at an event for a few months I'm afraid, those prices include p&p though

[harry hills]

Re: antweight/beetleweight parts clearout

cool, give us a week or two becuse im going on holiday shortly but thanks

[philippos]

Re: antweight/beetleweight parts clearout

i might be interested in one ot two of those things (although i live in sweden, can you post it here?)

i'd like to know the size and weight of the 2a motor controllers, the size and weight of the 4ch reciver, and also the weight of the wheels(might buy two!)


Cheers,

Philip J

Sweden :P

[josh]

Re: antweight/beetleweight parts clearout

Yep I can post to sweden no problem, wheels weigh about 3g each with tyres, the controllers are 51x16.6x11.4 at the largest points, weigh 6.5g each. The reciever is 29x13x4 at the largest points and weighs 1.2g

[philippos]

Re: antweight/beetleweight parts clearout

sounds very good, and 13 g for dual motor control is okay, since my only option otherwise is a sabertooth..

just one mor question: do you have another picture of the reciver, couldn't which one of the little boards was the reciver

will you charge extra for shipping all the way to sweden?

Regards,

Philip J

Sweden

[josh]

Re: antweight/beetleweight parts clearout

It's the blue board on the right, 2 up from the bottom. It doesn't have plugs but the pads on the board are quite large and easy to solder to. Shipping to sweden will be about 2 pound more at a geuss.

[PJ-27]

Re: antweight/beetleweight parts clearout

What sort of mixing is V-Tail? I'm yet to actually figure this out.....

[josh]

Re: antweight/beetleweight parts clearout

Standard mixing, to combine two sides to make forward backwards left and right on one stick.

[josh]

Re: antweight/beetleweight parts clearout

Fleaweight, brushless motor and 12amp esc sold.

[john_frizell]

Re: antweight/beetleweight parts clearout

How much for the weapon? You can message me.

[josh]

Re: antweight/beetleweight parts clearout

Sorry the weapon has been sold. The rest still available.